改性硅丙涂料Modified Silicone Coating

Self-leveling UV-resistant New Waterproof Material MS910

?Key Features

1.Odorless, Eco-friendly, No Harm to the Builder

2.Excellent Waterproof, Best Sealing, Bright Color

3.Excellent Aging resistance ,UV Resistance of 10 Years

4.Resistant to Oil, Acid, Alkali ,Puncture, Chemical Corrosion

5.Single Component, Self-leveling, Easy to Use, Convenient Operation

6.520%+ Elongation, Super-bonding without Crack

7,Resistance to Tear, Shifting, Settlement Joint

?Typical Applications

1.Waterproofing and moisture proofing for kitchen, bathroom, balcony,

roof and so on.

2.Anti-seepage of reservoir, water tower, water tank, swimming pool, bath,

fountain pool, sewage treatment pool and drainage irrigation channel.

3. Leak-proofing and anti-corrosion for ventilated basement, underground

tunnel, deep well and underground pipe and so on.

4. Bonding and moisture proofing of all kinds of tiles, marble, wood,

asbestos and so on.

?Technical Data Table

Note：All data above were tested under special condition (7 days after full cured).

?Directions for Use

First Step

Brushing the part like corner, tubes root. When operation,It should be considered

about the size, shape and environment of the construction area.

Second Step

Symmetrical scraping. The best thickness of the coating is no more than 2mm to

prevent the bubbles.

Protection:

If necessary,a proper protective layer can be operated on the surface of thecoating.

Cleaning: It can be soaked in toluene or xylene. It is strictly forbidden to immerse in alcohol

and other alcohol solvents.If it is not used for a long time, it should be cleaned

immediately with alcohol or other organic solvents. The cured glue can only be

scraped or torn off.

Preparation for Operation

 1. Tools ： The serrated plastic board, brush, plastic barrels, 30Kg electronics,

rubber gloves and cleaning tools like blade .etc

2. Environmental requirements：The temperature is 5~35 C and the humidity is

35 ~ 85%RH

3. Cleaning：The substrate surface must be solid, dry and be clean. Such as no

dust, grease, asphalt, tar, paint, wax, rust, water repellent, curing agent,

isolating agent and film. Surface cleaning can be dealt with by removing,

cleaning, blowing, and so on.

4.Make the substrate surface level：If there are cracks on the substrate surface,

first step is to fill them, and the surface should be leveled. Operation after the

sealant curing more than 3mm.

5.Theoretical dosage: 1.0mm thick, 1.3 Kg /㎡ coating needed.

• l Attention of operation

1. Don’t mix alcohol into the product, it will cause the product invalid. The tools with the

alcohol can’t be used before cleaning well.

2. The total coating thickness is around 2.0mm, special parts should be more than 2.0mm.

3. Avoid water, pollution and damage before tack free time of the coating,prohibit any

operation before full curing (about 24Hrs).

4. Ventilated environment is required as operating, and some necessary safety

precautions should be taken. During operation, records should be filled in truthfully. For

special projects, follow the construction description strictly.

5. Avoid contact with eyes and skin. If contact with your skin, scrub first with soap water

or alcohol, then rinse with water. If contact with your eyes, rinse with plenty of water, and

seek medical treatment immediately.

6. It is forbidden to build on the surface of the wet substrate.

7. Transportation: Avoid damp, high temperature,isolation and rain, far away from heat,

handle with care and prohibit extrusion collision.

?Packing and Storage

20KG/Drum,230Kg/Drum.

1. Sealed and stored in cool and dry place.

2. It is suggested to be stored at 5~25 ℃, and the humidity is less than 50%RH.

3. If the temperature is higher than 40 ℃ or the humidity is more than 80%RH, the shelf life may be shorter.

?Safety Operation Data

 MSDS isn't included here. Please read TDS, MSDS and label carefully before operation. You can get MSDS from SEPNA or other distributors, or mail to service center sepna@sepna.cc, or call  +86-400-882-1323.

?Warranty and Liability

All product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advices we supply don't apply in any circumstances. SEPNA don't make assurance of any other applications outside the specification until SEPNA supply a special written guarantee. SEPNA is only responsible to replace or refund if this product is defective within the warranty period stated above. SEPNA makes it clear that will not be liable of any accidents.